Uitnodiging voor een verjaardagsfeestje

#v12198

De uitnodiging en de decoratie zijn gemaakt van papier en kralen. De kleine hanger is gemaakt van verzilverd draad en past uitstekend bij de kleine jurk.

Selecteer producten bij dit idee

{{ optionsGroup.label }}

{{ getVariantsButtonText(option) }}
   
 
 
   
 
 
   
 
 
   
 
 
   
 
 
Totale prijs
{{ getFormattedBundlePrice() }}

{{ getRewardMessage() }}

Guide step %d
1   Cut out the dress, the collar and the petticoat from the template in matching colours.
Guide step %d
2   Assemble the parts with double-sided adhesive tape and 3D foam pads.
Guide step %d
3   Attach a ribbon around the waist of the dress and fasten it on the back. For the bow, cut a piece of ribbon measuring approx. 20cm, tie the bow and attach it to the belt with a 3D foam pad. Trim the ends. Decorate the small collar with self-adhesive rhinestone half-pearls.
Guide step %d
4   Cut a piece of silver-plated wire for the hanger. Double over the wire and twist a couple of times and form it. Bend the ends to form a small loop.
Guide step %d
5   Attach the hanger onto the card. Attach 3D foam pads and attach the hanger with another two 3D foam pads.
Guide step %d
6   Attach the dress to the hanger with 3D foam pads. Use two 3D foam pads on top of each other to achieve the same height as the hanger.
Guide step %d
7   Make a small border and attach it to the card with double-sided adhesive tape.
Guide step %d
8   For the bead coil, cut a piece of wire measuring 20cm. Pull beads onto the wire and twist the wire around a darning needle.
Guide step %d
9   Push a hole through the card and attach the bead coil.
Guide step %d
10   Cut a piece of paper. Attach the paper over the wire ends on the back with double-sided adhesive tape.
Guide step %d
13   Place Cards: Cut a piece of silver-plated wire measuring 25cm. Twist to form a small loop at the end. Pull seven red and seventy orange beads onto the wire.
Guide step %d
14   Bend the flower head around the silver-plated wire.
Guide step %d
15   Form the petals and close the flower.
Guide step %d
16   Pull a bead onto the end of the silver-plated wire.
Guide step %d
17   Cut a new piece of silver-plated wire and twist it around the stalk.
Guide step %d
18   Form the leaves.
Guide step %d
19   Twist the wire around the leaves.
Guide step %d
20   Pull a bead onto the end of the wire and bend to form a coil.
Guide step %d
21   Bend to form a hook for hanging onto the glass.
Guide step %d
22   Cut a piece of card for the place card which is attached onto the flower stalk with double-sided adhesive tape.
Guide step %d
23   A place card.
Guide step %d
24   A Napkin Ring: Make a flower following the same procedure as for the place card. Feed a 30cm long piece of wire through the middle of the flower, double over and twist.
Guide step %d
25   Bend the wire to a suitable size. Feed the wire through the middle of the flower.
Guide step %d
26   Twist the wire around the ring.
Guide step %d
27   The finished napkin ring.
Guide step %d
Patroon   -
Bijgevoegd bestand: Downloads
Al aangemeld? Download de sjabloon
Terug
Ik ben aan het winkelen als
Ga verder als guest
Uw voordelen van inloggen

✔ Uw persoonlijke verlanglijstje

✔ Bestelgeschiedenis bekijken

✔ Eenvoudig afrekenen
Uw voordelen van inloggen

✔️ Speciale prijzen

✔️ Speciale B2B-producten

✔️ B2B-marketingdomein
Uw voordelen van inloggen

✔ Content speciaal voor u

✔ Speciale prijzen
Copyright © Creativ Company | 2021-present